Denton, TX Heating & AC Repair, Installation and HVAC Service

Investigated a no-cool call for a split system. Found low refrigerant pressure. Leak detection procedures identified a pinhole leak in the evaporator coil. Discussing repair versus replacement options based on system age and refrigerant type (R-410A).

Finished a residential HVAC system experiencing intermittent blower motor failure. Diagnosis indicated a failing capacitor. Replacement with a like-for-like 5uF capacitor restored proper airflow. System amperage draw now within manufacturer specifications. Regular system checks can identify such issues proactively.

I arrived at a home in Brookside for a thermostat repair job. Customer complained that their thermostat was not working. The homeowner reported the heating system wasn’t responding. After testing the thermostat, I discovered the real issue was a faulty furnace ignitor. I replaced the ignitor, tested the system, and restored proper heating. The customer was relieved to have quick, accurate service.

Arrived at a home in Oakwood for an air duct repair job. The homeowner complained of high energy bills and poor airflow. I located and sealed leaks, replaced damaged duct sections, and cleared debris. After testing, airflow improved significantly. The customer noticed better HVAC performance. Contact us for expert air duct repair services!

I arrived in Southridge for an air duct repair job. The homeowner reported weak airflow and uneven cooling. I sealed leaks, reinforced connections, replaced damaged ducts, and removed debris. After testing airflow, the system ran efficiently. The customer noticed immediate improvements. Contact us for expert air duct repair services!

Performed annual maintenance on a Bryant Evolution furnace. Cleaned the burner assembly, inspected the heat exchanger for cracks, and tested the flame sensor. Checked and tightened all electrical connections and measured static pressure in the ductwork.

Repaired a Daikin DZ18TC heat pump that was tripping the breaker. The compressor's start capacitor had failed. Installed a new dual-run capacitor and checked the compressor amperage using a clamp meter. Verified that the unit operated without further trips.

Serviced a malfunctioning electric heater that wasn’t cycling properly. Found a defective limit switch using a continuity tester. Replaced the switch and inspected the heating elements for wear. Tested the heater to confirm proper cycling and heating performance.

Troubleshot a malfunctioning auxiliary heat system on a Rheem RP17 heat pump. The issue was due to a burned-out heat strip relay. Replaced the relay and tested the system in emergency heat mode, confirming proper auxiliary heat operation.

Performed routine maintenance on a Trane XR15 heat pump. Cleaned the condenser coils using a coil cleaner, checked the electrical connections, and tested the capacitor. Verified proper airflow and ensured the refrigerant charge was within acceptable limits.

I repaired a Lennox XP16 heat pump that was not blowing warm air. After inspecting the system, I found a faulty reversing valve. Replaced the valve and recharged the refrigerant to the correct level using an R-410A manifold gauge set.

I performed HVAC repair on a York system in Denton. The issue was a faulty capacitor that caused the AC to stop running. I replaced the capacitor, cleaned the condenser coils, and checked the refrigerant levels. The system is now operating smoothly and cooling effectively.

Today, I completed heating maintenance on a Carrier furnace in Denton. I inspected the heat exchanger, cleaned the burners, and replaced the air filter. I also tested the gas pressure and verified the thermostat calibration. The furnace is now ready for the colder months ahead.

I performed heating maintenance on a Lennox Elite EL296 gas furnace in Denton, TX last evening, ensuring it was ready for winter. I started by inspecting the heat exchanger for cracks and cleaning the burners to ensure proper combustion. I replaced the air filter with a 20x25x1 high-efficiency filter and lubricated the blower motor. The flame sensor was polished, and the gas valve was calibrated for optimal operation. Finally, I tested the safety switches and thermostat for functionality. The system passed all diagnostic tests and was running efficiently, providing reliable heating for the customer.

In Denton, TX, I completed routine maintenance on a Carrier Infinity 96 gas furnace. I inspected the heat exchanger for cracks, cleaned the burners, replaced the 16x25x1 air filter, and calibrated the thermostat for accurate temperature readings. The safety controls were tested, and the system was confirmed to be ready for the colder months ahead.

Repaired Lennox EL296V two-stage furnace with no heat complaint in Denton. Diagnosed failed pressure switch using digital manometer. Replaced switch with OEM part 103935-03. Cleaned flame sensor with fine-grit sandpaper. Verified inducer motor operation. Checked all limit switches. Adjusted blower speed for proper temperature rise. Cycled system through both stages to ensure proper operation. Restored heat to residence.

Performed fall maintenance on Daikin FIT heat pump system with gas furnace backup in Denton. Cleaned outdoor coil using coil cleaner and low-pressure rinse. Checked refrigerant charge, topped off R-410A. Cleaned condensate drain line with compressed air. Replaced air filter with MERV 11 pleated filter. Inspected ductwork and sealed accessible leaks with mastic. Cleaned flame sensor and checked ignition sequence on furnace. Calibrated Daikin One+ thermostat. Installed Daikin premium air purifier. Conducted static pressure test and adjusted blower speed for optimal airflow. Left system in peak condition for heating season.

I responded to a service call for an HVAC system that wasn’t cooling. After inspecting the unit, I found the condenser fan motor had failed, preventing heat from dissipating. I replaced the faulty motor with a new OEM condenser fan motor and checked refrigerant levels, which were within range. After cleaning the condenser coil, I tested the system, and it is now cooling the home efficiently.

I repaired a Goodman GSX140361 3-ton air conditioner that was short cycling. After diagnosing the issue, I discovered a faulty run capacitor and a clogged condensate drain line. I replaced the 45/5 MFD dual run capacitor with a new USA-made Titan Pro capacitor. Then, I cleared the condensate line using a Guardair pneumatic drain gun. Finally, I cleaned the evaporator coil with Nu-Calgon Evap Foam cleaner to improve efficiency. The unit now runs smoothly without interruption.

I addressed a Rheem RGGE-07EAUER gas furnace that wasn't producing heat. Upon inspection, I found a defective hot surface ignitor and a dirty flame sensor. I replaced the ignitor with a universal Silicon Nitride 120V model and cleaned the flame sensor using fine-grit sandpaper. I also replaced the air filter with a new MERV 11 pleated filter. After reassembly, I tested the furnace through multiple heating cycles to ensure proper ignition and heat production.

Completed an AC repair in Denton, TX, on a Lennox XC21 unit. Diagnosed a malfunctioning condenser fan motor and replaced it with a Lennox OEM part to restore proper airflow. Checked refrigerant levels and recharged with R-410A for optimal cooling efficiency. Inspected and cleaned the evaporator and condenser coils to ensure maximum performance. Regular maintenance and timely repairs are crucial for system longevity. For expert AC repair services, contact us for professional and reliable solutions in Denton, TX.

Installed a new Rheem RP1448AJ1NA 4-ton air conditioning system with Copeland Scroll two-stage compressor. Replaced existing air handler with Rheem RGRM upflow gas furnace utilizing EcoNet control board. Ran new 3/8" liquid and 7/8" suction refrigerant lineset using Diversitech LineSet Cover insulation. Fabricated return air plenum using SMACNA guidelines with Stamford Shortbody elbows. Triple evacuated to 500 microns using a Yellow Jacket SuperEvac vacuum pump. Charged with 10 lbs of R-410A refrigerant per specifications on data plate. Installed Rheem EcoNet WiFi thermostat with dehumidification control and enabled two-stage cooling/heating operations.

I performed annual HVAC maintenance on a Carrier system. Tasks included cleaning the condenser and evaporator coils, checking and adjusting refrigerant levels, and inspecting the blower motor. I also tested the capacitor and contactor, calibrated the thermostat, and lubricated all moving parts. The system was thoroughly tested to ensure optimal performance and efficiency for the upcoming season.

Installed a Rheem RP1448AJ1NA two-zone central air conditioning system in a residential home. Mounted the 4-ton outdoor condensing unit on a concrete pad using Rubber-A-Mounts for vibration isolation. Ran two separate sets of refrigerant lineset piping to indoor evaporator coils located in the attic space - one for the living room and one for the master bedroom. Used existing ductwork and installed motorized zone dampers to control airflow to each zone. Evacuated the entire system to 500 microns using a Fieldpiece EVAC4WAY vacuum pump. Charged with 3 lbs 8 oz of R-410A refrigerant per Rheem's specifications. Programmed the Rheem AccuLink zoning control board and verified proper cooling operation in each zone.

This afternoon, I investigated a noise issue with a Carrier central air conditioning system at a home in Denton, Texas. The homeowner reported an unusual rattling sound coming from the outdoor condenser unit. Upon inspection, I found that one of the condenser fan blades had become loose, causing it to vibrate against the fan housing. I carefully tightened the blade attachment and rebalanced the fan assembly. I also performed a general cleaning of the condenser coils and checked all electrical connections. The system is now operating quietly and efficiently, meeting the homeowner's expectations.